Tactical Rails And Accessories

FEATURES:
-Free floating
-Features a one piece barrel nut w/ no shims or clocking needed.
-All mounting hardware included
-Length: 12.5"
-Weight: 9.28oz

FEATURES
-M-LOK 5-Slot Accessory Rail
-2 5/16" long
-Allows you to mount sights, lights, & other tactical accessories to your free float M-LOK forend
-Can be placed at 3, 6 & 9 o'clock positions & can be joined to create continuous Pic Spec rail
-Made from 6061-T6 billet aluminum
-Adjusts in 1/2 slot increments for precise accessory placement
-No access to back side of the rail is required
-Accessories can mount with either end facing forward
-Includes M-LOK nuts, screws & hex wrench

FEATURES:
-Allows the attachment of various 1913 Picatinny rail-mounted acessories such as lights, vertical grips, etc
-Features beveled ends to reduce snagging & eliminate sharp corners & edges
-Solid Aluminum Construction
-3.1", 5 Slot
-Keymod

FEATURES:
Inside diameter 1.75"
Outside diameter 2.0"
1.95" over mounting flats
High quality MIL-STD 1913 top rail
One five slot Magpul M-LOK polymer rail section included
Construction from 6061 aluminum, hard coat anodized
Barrel nut and barrel nut wrench included
Weight: 11.2 oz
Made in USA

FEATURES
-7 slot
-6061 aluminum, hard coat anodized
-M-LOK mounting hardware included

FEATURES
-Made of aluminum
-Easy 1 screw installation

FEATURES:
-Aluminum body
-Lightweight aluminum barrel nut included
-3 M-LOK slots on 3 sides of front end of handguard
-Honeycomb lightening cuts
-Monolithic picatinny rail
-15" length

FEATURES
-KeyMod Picatinny Nylon Rail Section
-5.5"
-Flat Dark Earth
-Rail section is made of Lightweight Impact Resistant Polymer
-Mounting hardware is made of Corrosion Resistant Stainless Steel
-Made to the Mil-Standard 1913 Picatinny Arsenal Specifications
-Features a Snag resistant design, while retaining Mil-Standards specs
-Self-contained assembly, eliminates the possible loss of mounting hardware
-Fits ALL KeyMod interface mounting surfaces

NOTE: NYLON/POLYMER PICATINNY RAIL SECTIONS ARE FOR NON-LOAD BEARING ACCESSORIES ONLY. ALUMINUM PICATINNY RAIL SECTIONS RECOMMENDED FOR LOAD BEARING. DO NOT EXCEED 20 IN/LBS WHEN SECURING KEYMOD FASTENERS ON POLYMER ACCESSORIES. ALUMINUM PICATINNY RAIL SECTIONS MAY BE TORQUED TO 30 IN/LBS

FEATURES
-Allows you to quickly remove or attach items to picatinny rail
-Ideal for shorter optics/red dot sights that ou want to raise to co-witness lower in the window

FEATURES:
-6063 Extruded Aluminum
-M-Lok rail
-1913 Picatinny
-Black Nitride finish

FEATURES:
-4140 heat treated barrel nut
-Barrel nut & wrench included
-Features patented 4140 heat treated torque plate
-1913 picatinny top rail
-Two integral anti-rotation QD sling sockets
-7" length
-Weight: 6.8 oz

FEATURES
-7", Carbine Length
-No gunsmith drop-in installation, installs like factory plastic handguards
-Gen2 design with four anti-rotation QD sockets for push button swivels
-Incredibly lightweight, extremely solid lock-up with monolithic type continuous top rail
-High quality 1913 Mil-Spec rails, T-marked for location
-Constructed from 6061 aluminum, hard coat anodized
-Compatible with most gas piston systems

FEATURES
-Very low-profile 1913 Picatinny rail coverage
-Made of Santoprene material, a rubbery surface whichoffers improved weapon control & rail protection
-Easily cut for custom lengths
-Each panel fits one side of a carbine-length rail (18 slots)
-One panel per package

FEATURES
-Black finish
-Detachable
-Versatile, durable, heavy-duty stainless
-Raised cup around the push button to prevent accidental release

FEATURES:
-T6 Aluminum Body
-Fits 16" Carbines
- Hard Coat Anodized Aluminum
-Secures in place with four cross locking screws
-Mil-std 1913 Picatinny top rail
-M-LOK compatible
-Ultra lightweight
-7" length
-Direct drop in replacement for standard polymer forends

FEATURES
-For standard .925" barrels
-Keep debris out of your handguard while giving the front end of your firearm a unique look
-Do NOT fit YHM's S.L.R.® series of handguards

FEATURES
-Flat dark earth
-5 pack
-Made to fit ALL KeyMod mounting surfaces with seven (7) consecutive KeyMod slots
-Ultra-slim and radiused surface to allow a "round" handguard feeling
-Aggressive non-slip & non-reflective surface
-Ventilated for cooling
-Bi-directional locking tabs on either end
-5.55" x .625" x .10"
-Can be cut to any length
-Made in USA

FEATURES:
Length: 7.5"
Inside Diameter: 1.35"
Weight: 6 oz
Inner diameter: 1.350"
6061 T6 aluminum
Low Profile sleek design
Light weight for improved mobility
Steel barrel nut and mounting hardware included
1/2 inch sight distance increase for improved accuracy

FEATURES
-Four-piece
-Served as a lightweight, low-profile rail mounted indexpoint for improved weapon control, or as a forward
stop to prevent the shooter's hand from reaching the hot front sight assembly or muzzle
-Kit includes one Hand Stop, one Index Panel, one full XTM Enhanced Panel, & one XTM Enhanced Half
Panel

FEATURES
-Optimized design replaces original stamped receiver AK-47/AKM/AK-74 wooden or plastic hand guards
-Easy to install utilizing existing front hand guard retaining cap WITHOUT sling loop*
-Slots at the three, six, & nine o'clock positions for mounting direct-attach M-LOK accessories or M-LOK
1913 Picatinny rail sections
-Reinforced, heat-resistant polymer construction
-Integral, black oxide coated stainless steel heat shield
-Front lip & long side extensions shields hand from hot barrel while providing increased gripping surface
-Includes replacement polymer Top Cover
-Compatible with UltiMAK Optics Mount top cover
-Accepts factory cleaning rod

*Note: The MOE AK Hand Guard is a direct replacement for standard AK-47/AKM/AK-74 pattern hand guards & utilizes the existing hand guard retaining cap without sling loop. However, for those weapons with a retaining cap sling loop the MOE AK Hand Guard may be utilized if the loop is removed.

**Specifications based on factory configuration.

FEATURES:
Length: 9.5"
Width: 2.15"
Inside diameter: 1.3"
6061 Aluminum Type 3 Hard Coat Anodized
Barrel Nut and Wrench Included
2 Integral Anti-Rotation QD Sling Sockets
4140 Heat Treated Barrel Nut and Torque Plate
Weight: 11.8 oz
Made in USA

FEATURES:
-Allows the attachment of various 1913 Picatinny rail-mounted acessories such as lights, vertical grips, etc
-Features beveled ends to reduce snagging & eliminate sharp corners & edges
-Solid Aluminum Construction
-6", 15 Slot
-Stock AR

FEATURES
-7.28"L x 2.44"W x 2.44"H
-Top rail extends to upper receiver to form continuous mounting platform
-Clever top/bottom 2-piece design with integral spinal cords/alignment housing for perfect fit with
barrel nut & round front cap
-Made from aircraft aluminum with precision CNC machining & excellent anodizing/engraving
-Fits carbine length Model 4/15 & provides 4 Picatinny rails each with 14 slots
-Great zero-retention capability for all accessories installed on the rails
-Easy installation with no modification to the barrel
-Black rubber rail guards included
-Proudly made in the USA

FEATURES
-5 slots, max overall length of 2.5"
-For use with all M-LOK compatible hand guards & forends
-Allows the attachment of various 1913 Picatinny spec rail-mounted accessories
-Injection molded from a proprietary reinforced composite for enhanced strength & durability while
remaining lightweight
-Beveled ends reduce snagging & eliminate sharp corners & edges
-All hardware necessary for attachment directly to M-LOK slots on either aluminum or polymer
hand guard & forends if included

FEATURES:
Length: 6.75
Width: 4.9
Height: 1.55
Solid aluminum housing coupled with steel fasteners
Simple push button technology

FEATURES:
-Factory 1913 style picatinny rail for Mark IV™, Mark III™ & 22/45™
-Rail fits firearms w/ factory pre-drilled receivers
-Includes three screws
-DOES NOT FIT MARK I & MARK II PISTOLS

FEATURES:
Overall length: 8"
Width: 2.06"
Internal diameter: 1.8"
24 full M-Lok compatible slots and 4 half slots
Lightweight rugged construction of 6061 aluminum
Heat treated 4140 retaining clip with phosphate finish
One five slot M-Lok compatible rail section
Weight: 6.6 oz
Made in USA

FEATURES:
Fits Picatinny and Weaver style rails
Covers snap easily into place over exposed sections of rail
Lightweight Polymer
Durable weather and temperature resistant